TL;DR
- For final sterilizing filtration of a pharmaceutical liquid, shortlist a validated sterilizing-grade 0.2 or 0.22 µm finished filter supported for the intended use.
- Evaluate a 0.45 µm membrane when the job is clarification, solvent preparation or prefiltration and the application allows that rating.
- Chaoyue lists P120 at 0.22 µm and P80 at 0.45 µm, with separate bubble-point ranges for the two membrane grades.
- Ask for the test method, assembly specification and application evidence before approving a grade or supplier substitution.
In a 0.2 vs 0.45 micron membrane comparison, start with the duty at the point of use. A final pharmaceutical sterilizing filter needs documented performance for the finished device and intended process. A clarification membrane needs evidence that it removes the particles of concern and meets the required flow and compatibility targets. Nominal pore size helps identify candidates. The purchase decision depends on what the supplier can show for the exact grade and delivered construction.
When should you choose 0.2 or 0.22 µm?
Choose a qualified 0.2 or 0.22 µm finished filter when the final liquid filtration stage carries a sterility requirement and the device is supported for the intended application. FDA aseptic-processing guidance describes sterilizing-grade liquid filters as generally rated 0.2 µm or smaller. EU GMP Annex 1, section 8.79, specifies a maximum nominal pore size of 0.22 µm for the appropriately validated sterilizing-grade filter used when relevant liquids cannot be sterilized in their final container. The two documents concern pharmaceutical manufacture in their respective scopes. FDA aseptic-processing guidance. European Commission EU GMP Annex 1.
A 0.2 or 0.22 µm pore label supports shortlisting. A sterilizing-grade claim requires evidence for the exact finished filter. A nominal pore rating is the supplier’s stated size designation under its rating system. A sterile supplied device and a sterilizing-grade device describe different attributes. The first concerns the device’s condition as supplied. The second concerns its qualified filtration capability. A purchasing specification should identify which attributes are required and which documents establish each one.
Start by naming the part your organization actually approves. A membrane sold by width or roll length may be a component that a converter laminates, cuts or pleats. A capsule or cartridge includes a membrane together with joining surfaces, supports, housing and seals. Ask which of those configurations the technical document covers. If the response refers to a broad material family, keep the candidate at the material screening stage until the supplier connects the evidence to the finished part number.
When is a 0.45 µm membrane the better fit?
Choose 0.45 µm when the specification calls for particle clarification or an upstream stage and the finished membrane format meets that stage’s acceptance criteria. Chaoyue discusses solvent filtration as a use case in its 0.45um microporous membrane guide. For that use case, define the reason for filtration before requesting a quote. A buyer protecting an instrument from particulates will need the instrument or analytical method’s filter requirements, along with compatibility and background contamination data for the intended solvent.
A prefilter can intercept part of the incoming particle load, which can reduce loading on a downstream filter when those particles are responsible for its restriction. The benefit depends on the incoming material and the filter design. For a hypothetical clarification line with frequent downstream changeouts, compare the existing train with the proposed addition using observed throughput, interruptions and the costs of both stages. Include the extra filter, connections, receiving checks and disposal. A low unit price provides little information if the added stage contributes little capacity or introduces losses elsewhere.
For a straightforward particle-removal application, compare a 0.45 µm candidate with the cleanliness endpoint defined by the user of the filtrate. If the endpoint is missed, review the rating basis and particle data before changing pore size. If the endpoint is met and the application allows a single clarification stage, a finer grade would need a documented reason for selection, such as a stricter downstream specification.
How do Chaoyue P120 and P80 compare?
P120 is Chaoyue’s listed 0.22 µm ePTFE membrane and P80 is its listed 0.45 µm membrane. Use the codes to request grade-specific documentation. Expanded polytetrafluoroethylene, abbreviated ePTFE, is a porous material made by expanding PTFE. The category page reached through sterile-grade ePTFE membranes introduces bubble-point membrane media for evaluation. Its linked product detail provides the following material specifications. Final sterilizing-grade eligibility depends on additional evidence for the finished device.
| Decision field | P120 | P80 |
|---|---|---|
| Listed pore size | 0.22 µm | 0.45 µm |
| Listed bubble point | 120–150 kPa | 70–100 kPa |
| Listed width | Up to 1,400 mm | Up to 1,400 mm |
| Initial evaluation role | Fine membrane material screening. | Clarification or prefilter material screening. |
| Evidence to request | Grade test methods and, for final sterile duty, evidence for the exact finished filter. | Grade test methods and application data for particle removal and flow. |
The grade values above come from the Chaoyue ePTFE bubble-point membrane specification. The page lists the ranges without identifying the wetting liquid or detailed conditions in the specification table. Request the method before using those ranges for incoming acceptance or comparing them with another supplier’s data.

A bubble-point reading depends on how the membrane is wetted, so two pressure values are comparable only when the measurement basis is known. Bubble point describes the pressure associated with gas displacing wetting liquid from paths through the membrane under a defined test. Ask for the wetting liquid, temperature, specimen or device format and measurement criteria. Apply a finished filter’s qualified integrity-test limits to that device. A plain sheet’s catalog range and the acceptance criteria for a sealed cartridge refer to different test articles. FDA guidance on filtration and integrity testing.
Which specifications matter once the pore size is set?
Compare flow on a common test basis because fluid properties, effective area and construction can change the result even between products with the same nominal rating. Request the flow or differential-pressure data for the exact medium and configuration. Record whether the rate is stated per unit area or for a complete filter, and identify the fluid and temperature behind the value. If suppliers use different test fluids or pressure conditions, retain both sets of conditions on the comparison sheet. Ask for a like-for-like data set before using the numbers to size a purchase.
Check chemical compatibility for every wetted component, because the membrane, backing, seals and housing can respond differently to the same fluid. For a membrane supplied on a support, identify the support material and which side faces the fluid. With a finished filter, include housings, seals and other product-contact materials in the review. Document the liquid composition and application temperature range so the supplier can identify the scope of its compatibility statement. Where contact material can affect a sensitive analytical result, also define what blank or material documentation the method owner needs.
Wettability is the tendency of a liquid to spread across and enter a material. A membrane described as hydrophobic can behave differently with water and with a solvent that wets it readily. State whether the project uses water, an organic solvent or a mixture. Ask whether the grade is supplied untreated or surface modified, and whether the compatibility and flow data apply to that version. The delivered format and treatment should appear on both the sample label and the production specification.
What belongs in a supplier qualification request?
Write the intended filtration role and grade code on the request, then list the evidence needed to move from a sample to an approved part. A request for membrane stock should identify the desired width, format and converting requirements. A request for a finished filter should name the device format and approved application. Ask for the current datasheet, a lot-linked sample identifier and an example of the batch documentation. For a final sterilizing claim, ask for the relevant validation documentation tied to the finished part and have the responsible quality team review its applicability. EU GMP Annex 1, filter sterilisation.
Keep the approved sample identifier and specification revision on the purchase record so that production lots can be checked against what was evaluated. Chaoyue’s sterile filtration FAQ link leads to its general supplier FAQ, which outlines inquiry, quotation, sample confirmation and production. Use that sequence to agree which documentation travels with the sample and subsequent lots. If your organization requires advance notice of changes, identify the materials, treatments, structures and test methods covered by the agreement.
For example, a replacement roll could have the same grade code and quoted width while arriving on a different support. The support may change how the roll handles during conversion or which surfaces touch the product. Document the discrepancy against the agreed revision and refer it to the specification owner before accepting the change. When the approved item is a finished filter, a change to the assembled part should follow the applicable qualification and change-control procedure.
How should buyers compare quotes for different formats?
Compare roll quotes by usable area and finished-filter quotes by approved device configuration. A quoted roll width tells you the upper limit on the material across the web. The usable amount depends on what the converter can accept, including edge allowances and any format or handling constraints defined on the purchase specification. Request the delivered roll dimensions and ask how the supplier identifies unusable sections. For a finished assembly, record the model, connection type and effective area if disclosed, along with what is included in the price.
For a hypothetical distributor comparing two offers for the same clarification job, one quote might cover membrane stock and the other might cover a ready-to-install device. The membrane quote leaves converting, assembly and verification as separate activities. Include those activities when building the comparison, and identify which party owns each acceptance step. For recurring orders, specify how the supplier marks the grade and lot on each package and which records accompany a shipment. This allows the receiving team to trace a discrepancy to a specific lot without relying on packaging appearance or the generic micron rating.
Frequently asked questions
Can a 0.45 micron membrane replace a final sterilizing filter?
For the pharmaceutical liquid applications discussed here, keep the qualified sterilizing filter in the final position. Consider a 0.45 µm membrane upstream when the process needs clarification and the added stage has a documented benefit.
Are 0.2 and 0.22 micron filters interchangeable?
Both labels are used for fine filtration products, but each finished filter needs evidence for its intended use. Review the exact grade, construction and approved substitution procedure before changing part numbers.
Does a bubble point establish sterilizing-grade performance?
A bubble-point result describes a filter tested under a specified method. Sterilizing-grade qualification requires separate retention evidence and a documented relationship between the integrity test and the filter’s performance.
Is Chaoyue P120 a finished sterile filter?
Chaoyue lists P120 as 0.22 µm ePTFE membrane material. Buyers evaluating a finished filter need documentation for the assembled device, its packaging or supplied sterility status, and its intended application.
Will a 0.45 micron membrane always give higher flow?
Flow depends on the material, area, assembly and test conditions as well as the pore rating. Compare data obtained with the same fluid, temperature and pressure basis before accepting a flow advantage.
What should a buyer include in a membrane inquiry?
State the filtration role, fluid, format, material requirements and evidence the quality team needs. Ask for the grade code, datasheet, sample identification and the test method behind each requested specification.
Request a grade-specific quotation
For a clarification or prefilter inquiry, specify the target, format and fluid, and request P80 documentation if 0.45 µm fits the application. For fine media screening, reference P120 and identify whether you need membrane stock or a finished device with qualification evidence. Include the expected order quantity and any lot traceability requirements so the quote can be checked against the sample and the approved specification. Contact Chaoyue.
Post time: Nov-19-2026
